Fundamental Plumbing Insights for Bathtub Installation

Call

Almost everyone maintains his or her own piece of advice on the subject of A Step-by-Step Guide to Installing a Bathtub.


How to Install a Bathtub Yourself
Setting up a bath tub isn't precisely brain surgery, but it does call for solid plumbing, woodworking, as well as in some cases, tiling skills. Replacing an old bathtub with a new one is also a reasonably tough job. If the old tub is readily available, the project can relocate immediately; if you need to open a wall to remove the old tub as well as position the brand-new bathtub, the task is a lot harder. In either situation, the job is within a residence handyman's skills, although you will require a helper to move out the old tub and also set in the brand-new one. Ensure you have qualified on your own for the work and also are comfortable trying it. Rather than employing a professional to take control of a halfway-completed project, it is much better to consider employing one before you begin. Chances are you may require a professional plumber to make tube connections.
This short article will certainly help you mount a brand-new tub in your washroom if you have currently acquired a brand-new tub as well as don't need to transform the plan of your previous water system pipelines.
Your tools as well as material checklist ought to make up the following:
  • New Bathtub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Blade

  • Tape Measure

  • Pipe Caps


  • Preparing for the Installment


    To start with, the sustaining framework provided with the bath must be fitted (if called for) according to the manufacturer's directions. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is essential to make sure that if the faucet includes a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the taps device to avoid pressure on the tub.
    Fit the adaptable faucet ports to the bottom of the two taps using 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet with the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Make certain you utilize every one of the provided washers.
    Connect the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bathroom ought to currently prepare to be fitted in its final placement.

    Removing Old Touches


    If you require to replace old faucets with brand-new ones as a part of your installment, then the first thing you need to do is detach the water supply. After doing so, turn on the taps to drain pipes any water remaining in the system. The process of getting rid of the existing faucets can be fairly bothersome as a result of the restricted access that is typically the situation.
    Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the faucets. Have a towel prepared for the remaining water that will come from the pipelines. When the supply pipelines have been gotten rid of, make use of the same device to loosen the nut that holds the taps onto the bath/basin. You will need to stop the solitary taps from transforming during this procedure. Once the faucets have been removed, the holes in the bath/basin will certainly need to be cleaned of any type of old securing compound.
    Prior to going on to fit the new faucets, compare the pipe connections on the old taps to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new taps to fit.

    Installing the Tub


    Making use of the two wood boards under its feet, place the tub in the required placement. The wooden boards are valuable in uniformly spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 little points.
    The next goal is to guarantee that the bathtub is leveled all round. This can be attained by examining the spirit level and readjusting the feet on the bathtub up until the spirit level checks out degree.
    To set up faucets, fit all-time low of the furthest flexible tap port to the suitable supply pipeline by making a compression join; then do the exact same for the other tap.
    Activate the water system and also examine all joints as well as new pipework for leakages and tighten them if required. Load the tub as well as also examine the overflow outlet and also the normal outlet for leaks.
    Ultimately, deal with the bath paneling as described in the supplier's instruction manual. Tiling as well as securing around the tub must wait up until the bathtub has actually been made use of a minimum of once as this will resolve it right into its final placement.

    Suitable New Touches


    If the tails of the new taps are plastic, then you will certainly require a plastic adapter to avoid damage to the string. One end of the port fits on the plastic tail of the tap as well as the various other end offers a connection to the current supply pipes.
    If you require to fit a monobloc, then you will certainly need decreasing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
    Next, position the tap in the installing opening in the bath/basin guaranteeing that the washing machines remain in area between the tap and also the sink. Secure the faucet in position with the maker provided backnut. Once the faucet is securely in position, the supply pipes can be attached to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with normal faucet adapters. The former type needs to be connected to the tap finishes initially, tightening just by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have been linked.

    Tiling Around the Bathtub


    In the area where the bathroom meets the tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the fitting can relocate sufficient to crack a rigid seal, causing the water to penetrate the wall between the bathroom as well as the tiling, causing issues with moisture and feasible leakages to the ceiling below.
    You can choose from a selection of coloured sealers to assimilate your fixtures and also installations. They are sold in tubes and also cartridges, as well as can sealing voids up to a width of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of soaked paper or soft rope. Remember to always fill the bath tub with water before securing, to permit the motion experienced when the bathtub remains in use. The sealer can crack relatively very early if you do not take into consideration this activity prior to sealing.
    Additionally, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are likewise conveniently available on the market. It is recommended to fit the ceramic tiles making use of water-resistant or water-proof sticky as well as grout.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub Yourself

    As a reader about A Step-by-Step Guide to Installing a Bathtub, I imagined sharing that excerpt was a good idea. For those who liked our blog post kindly do not forget to share it. We take joy in reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.


    Booking Page

    Leave a Reply

    Your email address will not be published. Required fields are marked *